Raspberry pi- Trainer board & robotics- lab-32/16/8

Order Code: 18193308.1.4

Category: General Lab Equipment III

Specification of avr trainer board: Program debugging function by PC Software Raspberry pi software 1.2.3 Program download and trace function Display the register contents Memory contents modification and dump function Various Command ...



SPECIFICATION

  • Specification of avr trainer board:
  • Program debugging function by PC
  • Software Raspberry pi software 1.2.3
  • Program download and trace function
  • Display the register contents
  • Memory contents modification and dump function
  • Various Command function
  • Included stepper motor interface circuit
  • DOT MATRIX unit
  • LCD display unit
  • DIA and AID converter experiment
  • Sound experiment with Speaker
  • Interrupt experiments
  • Thermistor Sensor
  • Bar LED unit
  • Key board experiment
  • External interface connector
  • Display the current BUS status on LED
  • Specification of Rovers robotics chassis:
  • Adjustable gear box angles
  • min. 4 independent DC motors
  • min. 4 independent hall effect encoders
  • Thick rubber tank treads
  • min. 6x AA battery holder
  • min. 10Kg/cm stall torque per motor

Description:
If you're looking for a base for your next robot, look no further than the Rover 5. The Rover 5 uses 4 independent motors, each with an optical quadrature encoder and gearbox. The entire gearbox assembly can be rotated at min. 5-degree increments for different clearance configurations. You can even replace the tank treads with traditional wheels.
This isn't a wimpy or flimsy robot base. Weighing in at over 2.5 pounds without batteries, this base is heavy duty and can drive over quite a bit. Check the manual below for dimensional drawings. We now stock acrylic expansion plate for this rover.

 

  • Specification of Raspberry-pi iot learner kit
  • Quad Core --1.2GHz Broadcom BCM2837 64bit CPU
  • min. 1GB RAM BCM43438 Wi-Fi and Bluetooth Low Energy (BLE) on board
  • min. 40-pin Extended GPIO
  • min. 4x USB 2 ports
  • min. 4 Pole stereo output and composite video port
  • Full size HDMI
  • CS! camera port for connecting a Raspberry Pi camera
  • DSI display port for connecting a Raspberry Pi touchscreen display
  • Micro SD port for loading your operating system and storing data
  • Upgraded switched Micro USB power source up to 2.5A
  • Sense HAT features:
  • Official Sense HAT from the Raspberry Pi Foundation
  • min. 8x8 LED matrix display
  • Accelerometer, gyroscope and magnetometer
  • Air pressure sensor
  • Temperature and humidity sensor
  • Small joystick
  • Power Supply Features:
  • min. 1.5m Micro USB
  • min. 4 changeable heads for use in the UK, Europe, Australia & US regions
  • Current rating: min. 2.5A
  • Raspberry Pi Case features:
  • Designed to house the Raspberry Pi B , Raspberry Pi 2, Raspberry Pi 3 and HAT PCBs
  • HAT can be removed without removing the Raspberry Pi from the enclosure
  • All cut-outs are pre-cut into the case
  • Camera ribbon slot in enclosure lid
  • Display ribbon slot in enclosure lid
  • Label recess on enclosure base
  • Gloss finish

 

  • Specification ofrobobuilder robot :
  • Specification    Details
  • Size/Weight    min. 28.5x17x5x10.5cm/1.25kg
  • DOF(Degree of Freedom)    min. 16 servo motors
  • IR sensor    Obstacle detection
  • Sound sensor    Sound detection
  • Acceleration sensor    Gravity detection
  • Bartery(11V Li-poly)    min. 30 minutes Approx.
  • Bluetooth    Optional
  • External case    Engineering plastic

 

  • Specification of mavic pro dron:
  • Product Position: Entry-Level Professional Drone with Powerful Obstacle Avoidance Weight (Battery & Propellers Included): min. 1388 g
  • Max Flight Time: Approx. min. 30 minutes
  • Vision System: Forward Vision SystemBackward Vision SystemDownward Vision System Obstacle Sensing: Front & Rear Obstacle Avoidance Left & Right Infrared Obstacle Avoidance Camera Sensor: 1" CMOSEffective pixels: min. 20 M
  • Max. Video Recording Resolution: min. 4K 60P
  • Max Transmission Distance: FCC: min. 4.3 mi
  • Video Transmission System: Lightbridge
  • Operating Frequency: 2.4 GHz-5.8 GHz
  • *min. 5.8 GHz transmission is not available in some regions due to local regulations. Specification of submarine radio control simulation series:

 

  • Specifications
  • Name    Simulation Series RC Submarine Toy
  • Model    777 - 216
  • Age    min. Above 8 years old
  • Remote Control    Radio control
  • Remote Control Distance min. Above 4m
  • RC Submarine Battery    Ni-MH battery min. 3.6V/120mAh (included)
  • Transmitter Battery    min. 4pcs AA 1.5V (not included)
  • Charging Time    min. Above 10 mins
  • Playing Time    About min. 8 mins
  • Package Size    min. 16 x 8 x 10 cm
  • Package Contents
  • min. 1 x 777 - 216 Simulation Series RC Submarine Toy, 1 x Transmitter, 1 x An Manual

 

  • Specification of Dremel 3D printer:
  • Extruder: Single extrusion
  • Extruder temperature: Up to 230°C /397°F
  • Operating Interface: min. 3.5" full color IPS touch screen
  • Maximum Build Volume: 9" x 5.9" x 5.5" / 230 mm x 150 mm x 140 mm
  • Layer Thickness: min. 4 mil I 0.004 inches 100 microns 10.10 mm
  • SD Card: Up to 32GB in size /3D20 will not work with SD cards larger than 32GB
  • Internal Storage: min. 4GB
  • Weight (without spool)
  • min. 19 pounds 8 az (8.845 kg) Dimensions
  • Height: min. 15.7 inches (400 mm)
  • Width: min. 19.1 inches (485 mm)
  • Depth: min. 13.2 inches (335 mm)

 

  • Specification of touch s 3D printer:
  • Product size: min. 275 x 275 x 470mm (W x D x H)
  • Weight :8.9kg
  • Print type: FFF (Fused Filament Fabrication) Printer structure: Delta type
  • Build size: min. 0150 x 160mm
  • Bed: Stainless steel + Special Coated Film
  • Auto leveling: 0 Extruder: Single Nozzle size: min. 0.4mm
  • Layer thinness: 0.05mm — 0.3mm
  • Positioning precision: min. 0.01mm
  • Filaments: PLA / ABS 1.75mm
  • Power: Adapter DC12V/10A
  • Control panel: min. 4.3" Touch LCD
  • CPU: min. 68MHz 32bit ARM CPU
  • Manufacturer    Authorization    Letter    from    with    contract    details    and    Original    or    Color    Printed
  • Catalogue/Brochure-
  • [should be submitted by the bidder]
  • User manual — [should be submitted on delivery by the bidder]
  • Warranty: min. 01(One) with services- Installation, Testing & Commissioning should be provided by the qualified Engineers 

Enquiry Form