Electricity and semiconductors training system

Order Code: 21224672.6

Category: General Lab Equipment III

Electricity Lab & Power Electronics Lab ELECTRICITY LAB Electricity Lab” is a versatile training kit for a laboratory. It is designed such that all the basic electrical circuits can be tested with the help of this trainer kit. The e...



SPECIFICATION

Electricity Lab & Power Electronics Lab

ELECTRICITY LAB

Electricity Lab” is a versatile training kit for a laboratory. It is designed such that all the basic electrical circuits can be tested with the help of this trainer kit. The experiments given with the training system develop mental starting from an introduction to the circuit, fundamentals and experiments on Ohm's Law, Magnetism, Relay, Power, Lenz's Law, Motors, Diode, Kirchoff's Law, R, L, C and many more. This simple training lab provides a strong foundation for future studies in electrical or electronics. This takes students from the basics of Ohm's law, through simple series and parallel circuit analysis and into the same elementary aspects of electronics where they will build circuits using capacitors and diodes. With this system, a set of coils and cores are provided. These high-quality coils (Labelled with several turns) and laminated iron cores provide an effective introduction to electromagnetic theory.

 

POWER ELECTRONICS LAB

Power Electronics Lab is used to perform power electronics circuit experiments. It is beneficial in power electronics laboratories for performing power experiments in colleges and universities. Students need to know about the characteristics of power electronic devices and the applications of power devices. The applications or power devices are alarm circuits, lamp flashers, rectifiers, choppers, and inverters. It is also used for commutation circuits.

Technical Specifications:

DC Power Supply on Board: ± 5V at 100mA

: ± 12V at 150mA

: ± 15V at 50mA

: ± 35V at 50mA

AC Power Supply on Board : 18V - 0V - 18V at 50mA

: 15V - 0V - 15V at 50mA

Triggering Circuit on Board: 5 gate signal output

Frequency range : 40Hz to 900Hz Variable

Amplitude: 12V

PWM control of G1,G2,G3 and G4 Duty

cycle control of the “Gate” Signal is 0 to 100%

Single Phase Rectifier: Firing angle control 0°-180° variables

Firing Circuit on Board: Four gate signal output with isolation

SCR Assembly: 4 SCRs 2P4M, 600V,2A

Power Devices : IGBT-G4BC20S, MOSFET-IRF540, UJT-2N2646, DIAC-DB3, TRIAC-BT136, PUT-2N6027

Circuit Components On Board : Capacitor 0.01uF, 0.047uF , 0.1uF, 0.33uF, 1uF/63V(4Nos.) 2.2uF/50V

Diode 1N4007 (8Nos.)

Zener Diode 9V (1Nos. )

Inductors 10mH, (1Nos.), 68mH (2Nos.)

Load Resistance 120E, 270E, 1K, 2K2, each 5W

Resistance on Board (½ W) 22E/5W, 100E/2W, 220E/2W

Resistance on Board(1/4W) 10K (3Nos.), 22K,33K,47K,

Potential Meter 4K7(2Mos.), 1M(1Nos.)

Pulse Transformer on Board : 2 Nos. PT4502, 1:1 and one is PT4503 1:1:1

Toggle Switch : SPST (1Nos.)

Power Requirements : 220V ±10%, 50Hz

The Equipment is Useful for Students at engineering / technical institutes (EC & Telecom) Technical training centres in communication organizations, R&D personnel and practising engineering in research labs and industry.Electricity Lab & Power Electronics Lab

ELECTRICITY LAB

Electricity Lab” is a versatile training kit for a laboratory. It is designed such that all the basic electrical circuits can be tested with the help of this trainer kit. The experiments given with the training system develop mental starting from an introduction to the circuit, fundamentals and experiments on Ohm's Law, Magnetism, Relay, Power, Lenz's Law, Motors, Diode, Kirchoff's Law, R, L, C and many more. This simple training lab provides a strong foundation for future studies in electrical or electronics. This takes students from the basics of Ohm's law, through simple series and parallel circuit analysis, into the the same elementary aspects of electronics, where they will build circuits using capacitors and diodes. With this system, a set of coils and cores are provided. These high-quality coils (Labelled with several turns) and laminated iron cores provide an effective introduction to electromagnetic theory.

 

POWER ELECTRONICS LAB

Power Electronics Lab is used to perform power electronics circuit experiments. It is beneficial in power electronics laboratories for performing power experiments in colleges and universities. Students need to know about the characteristics of power electronics devices and the applications of power devices. The applications or power devices are alarm circuits, lamp flashers, rectifiers, choppers, and inverters. It is also used for commutation circuits.

Technical Specifications:

DC Power Supply on Board: ± 5V at 100mA

: ± 12V at 150mA

: ± 15V at 50mA

: ± 35V at 50mA

AC Power Supply on Board : 18V - 0V - 18V at 50mA

: 15V - 0V - 15V at 50mA

Triggering Circuit on Board: 5 gate signal output

Frequency range : 40Hz to 900Hz Variable

Amplitude: 12V

PWM control of G1,G2,G3 and G4 Duty

cycle control of the “Gate” Signal is 0 to 100%

Single Phase Rectifier: Firing angle control 0°-180° variables

Firing Circuit on Board: Four gate signal output with isolation

SCR Assembly: 4 SCRs 2P4M, 600V,2A

Power Devices : IGBT-G4BC20S, MOSFET-IRF540, UJT-2N2646, DIAC-DB3, TRIAC-BT136, PUT-2N6027

Circuit Components On Board : Capacitor 0.01uF, 0.047uF , 0.1uF, 0.33uF, 1uF/63V(4Nos.) 2.2uF/50V

Diode 1N4007 (8Nos.)

Zener Diode 9V (1Nos. )

Inductors 10mH, (1Nos.), 68mH (2Nos.)

Load Resistance 120E, 270E, 1K, 2K2, each 5W

Resistance on Board (½ W) 22E/5W, 100E/2W, 220E/2W

Resistance on Board(1/4W) 10K (3Nos.), 22K,33K,47K,

Potential Meter 4K7(2Mos.), 1M(1Nos.)

Pulse Transformer on Board : 2 Nos. PT4502, 1:1 and one is PT4503 1:1:1

Toggle Switch : SPST (1Nos.)

Power Requirements : 220V ±10%, 50Hz

The Equipment is Useful for Students at engineering / technical institutes (EC & Telecom) Technical training centres in communication organizations, R&D personnel and practising engineering in research labs and industry.Electricity Lab & Power Electronics Lab

ELECTRICITY LAB

Electricity Lab” is a versatile training kit for a laboratory. It is designed such that all the basic electrical circuits can be tested with the help of this trainer kit. The experiments given with the training system develop mental starting from an introduction to the circuit, fundamentals and experiments on Ohm's Law, Magnetism, Relay, Power, Lenz's Law, Motors, Diode, Kirchoff's Law, R, L, C and many more. This simple training lab provides a strong foundation for future studies in electrical or electronics. This takes students from the basics of ohm's law, through simple series and parallel circuit analysis, into the same elementary aspects of electronics, where they will build circuits using capacitors and diodes. With this system, a set of coils and cores are provided. These high-quality coils (Labelled with several turns) and laminated iron cores provide an effective introduction to electromagnetic theory.

 

POWER ELECTRONICS LAB

Power Electronics Lab is used to perform power electronics circuit experiments. It is beneficial in power electronics laboratories for Performing power experiments in colleges and universities. Students need to know about the characteristics of power electronics devices and the applications of power devices. The applications or power devices are alarm circuits, lamp flashers, rectifiers, choppers, and inverters. It is also used for commutation circuits.

Technical Specifications:

DC Power Supply on Board: ± 5V at 100mA

: ± 12V at 150mA

: ± 15V at 50mA

: ± 35V at 50mA

AC Power Supply on Board : 18V - 0V - 18V at 50mA

: 15V - 0V - 15V at 50mA

Triggering Circuit on Board: 5 gate signal output

Frequency range : 40Hz to 900Hz Variable

Amplitude: 12V

PWM control of G1,G2,G3 and G4 Duty

cycle control of the “Gate” Signal is 0 to 100%

Single Phase Rectifier: Firing angle control 0°-180° variables

Firing Circuit on Board: Four gate signal output with isolation

SCR Assembly: 4 SCRs 2P4M, 600V,2A

Power Devices : IGBT-G4BC20S, MOSFET-IRF540, UJT-2N2646, DIAC-DB3, TRIAC-BT136, PUT-2N6027

Circuit Components On Board : Capacitor 0.01uF, 0.047uF , 0.1uF, 0.33uF, 1uF/63V(4Nos.) 2.2uF/50V

Diode 1N4007 (8Nos.)

Zener Diode 9V (1Nos. )

Inductors 10mH, (1Nos.), 68mH (2Nos.)

Load Resistance 120E, 270E, 1K, 2K2, each 5W

Resistance on Board (½ W) 22E/5W, 100E/2W, 220E/2W

Resistance on Board(1/4W) 10K (3Nos.), 22K,33K,47K,

Potential Meter 4K7(2Mos.), 1M(1Nos.)

Pulse Transformer on Board : 2 Nos. PT4502, 1:1 and one is PT4503 1:1:1

Toggle Switch : SPST (1Nos.)

Power Requirements : 220V ±10%, 50Hz

The Equipment is Useful for Students at engineering / technical institutes (EC & Telecom) Technical training centres in communication organizations, R&D personnel and practising engineering in research labs and industry.

Enquiry Form