Digital and Analog Bread Board Laboratory Trainer

Order Code: 23246945.11

Category: General Lab Equipment III

33503C DIGITAL-ANALOG KIT is intended for elementary as well as advance training of Digital & Analog electronics. The trainer covers regular digital & analog circuits by solder-less interconnections on breadboard and as well as compatible wit...



SPECIFICATION

33503C DIGITAL-ANALOG KIT is intended for elementary as well as advance training of Digital & Analog electronics. The trainer covers regular digital & analog circuits by solder-less interconnections on breadboard and as well as compatible with all optional modules, through use of 2mm brass terminals and patch cords. Clock generators, logic level input/output indicators and DC power supplies etc. are inbuilt. The unit housed in attractive enclosure is supplied with mains cord, patch cords, Instruction manual and Component Set.

Features:

  • Bread Board:Unique solder-less large size, spring loaded breadboard consisting of two Terminal Strips with 1280tie points and 4 Distribution Strips with 100 tie points each, totaling to 1680 tie points. Size:112mm x                        170mm approx)
  • Fixed Power Supply : +5 V, -5 V, +12 V, and -12 V
  • AC Supply : 15-0-15V. Can be used as15V
  • Fixed Clock : 1Hz, 10Hz,100 Hz, 1KHz, 10KHz, 100KHz, 1MHz.
  • Manual Pulser Switch : 1 independent buffered bounce free manual pulser (useful for freezing the action of each stage of the counter after every clock pulse)
  • 10 Logic Level Input : 10 independent logic level inputs to select High / Low TTL levels, each with a LE to indicate high / low status and termination
  • Logic Level Indicator : 10 independent buffered logic level indicators for High / Low status indication of digital outputs.
  • Potentiometer : 1 Potentiometer (10K) with terminals
  • On Board Switches : 2 Switches signal pole double through
  • Logic Probe : Logic level indicator for TTL/CMOS
  • Power : 230 V ± 10%, 50 Hz
  • Accessories : Mains cord, Operating and Experimental manual, Red & Black patch cords (2mm with Pin) 10 each, Red & Black patch cord (Pin to Pin) 10 each & Component Set
  • Instruction manual : Strongly supported by detailed operating instructions

Experimental Coverage:

Analog

  1.  Study of Diodes in DC circuits
  2.  Study of Light Emitting Diodes in DC Circuits
  3.  Study of Half wave rectifier
  4.  Study of Full wave rectifier
  5.  Study of Zener Diode as a voltage regulator
  6.  Study of transistor series voltage regulator 07. Study of transistorshunt voltage regulator Optional
  7.  Study of Low pass filter
  8.  Study of High pass filter
  9.  Study of band pass filter
  10.  Study of CE configuration of NPN transistor
  11.  Study of CB configuration of NPN transistor
  12.  Study of CE amplifier
  13.  Study of Monostable multivibrator using transistor
  14.  Study of Bistable multivibrator using transistor
  15.  Study of 8 to 3 Line Encoder

Digital

  1.  Logic gates operation
  2.  To prove De-Morgan's theorem with Boolean logic equations
  3.  Binary to Gray code conversion
  4.  Gray code to Binary conversion
  5.  Binary to Excess-3 code conversion
  6.  Binary Addition and Subtractor
  7.  Binary Multiplier
  8.  EX-OR gate implementation
  9.  Application of EX-OR gate
  10.  Johnson Counter
  11.  To verify the dual nature of Logic Gates
  12.  Study of Flip-Flops RS, JK, D&T
  13.  Multiplexer and Demultiplexer
  14.  4 Bit Binary up and down counter
  15.  Study of 8 to 3 Line Encoder
  16.  Study of 3 to 8 Line Decoder
  17.  Study of Shift Register (SIPO)


Optional

  1.  CMOS-TTL Interfacing
  2.  Study of Crystal oscillator
  3.  Study of pulse stretcher circuit

Enquiry Form