DC Power Electronics Training System

Order Code: 19204149.32

Category: General Lab Equipment III

The pack contains:  Three-Module Workstation Low-Voltage Resistive Load Filtering Inductors/Capacitors Lead-Acid Battery Pack IGBT Chopper/Inverter Connection Lead Set Four-Quadrant Dynamometer/Power Supply Data Acquisition an...



SPECIFICATION

  • The pack contains: 
  • Three-Module Workstation
  • Low-Voltage Resistive Load
  • Filtering Inductors/Capacitors
  • Lead-Acid Battery Pack
  • IGBT Chopper/Inverter
  • Connection Lead Set
  • Four-Quadrant Dynamometer/Power Supply
  • Data Acquisition and Control Interface
  • 24 V AC Power Supply
  • Power Requirements:
  • Service Installation  : A standard single-phase ac outlet
  • Computer Requirements :  A currently available personal computer with USB 2.0
  • ports, running under one of the following operating systems: Windows® 7 or Windows® 8.
  • Physical Characteristics: Dimensions (H x W x D) 900 x 930 x 530 mm (35.4 x 36.6 x 20.9 in)
     
  • Three module workstation: The Three-Module Workstation consists of a single row of three full-height compartments that can accommodate up to three full-size EMS modules or six half-size EMS modules.
  • Low-Voltage Resistive Load :120/208 V – 60 Hz
  • Filtering Inductors/Capacitors: This Filtering Inductors/Capacitors module consists of two separate filters enclosed in a half-size EMS module: a low-frequency filter and a high frequency filter. The low-frequency filter consists of an inductor and a polarized capacitor, while the high frequency filter consists of two inductors and a non-polarized capacitor. Internal electrical components are identified on the module front panel. 4 mm banana jacks provide access to the different components in the module.
  • Lead-Acid Battery Pack Battery Pack: 
  • Type: 4 valve-regulated lead-acid batteries
  • Voltage: 48 V (12 V for each battery)
  • Capacity: 9 Ah
  • Maximum Charge Current: 2.7 A
  • Maximum Discharge Current :  7 A
  • Parallel Charging Input :  58V maximum
  • Overcurrent Protection
  • Battery Pack Fuse : 10A
  • Test Point Limiting Resistors (3): 1 kΩ
  • Maximum Current : 6 A
  • Filtering Capacitor : 450 μF
     

Protections

  • DC Bus Overvoltage:880 V
  • DC Bus Circuit Breaker:6 A
  • IGBT Electronic Overcurrent: 12 A
  • IGBT Overheat About: 70°C

Dumping Circuit

  1. Voltage Threshold: 660 V
  2. Connection Lead Set
  3. 4mm Safety Banana Plug Leads Characteristics
  4. Cross Section:1 mm²(1974 cmil)
  5. Rated Current: 19 A
  6. Rated Voltage: 600 V, CAT II
  7. 4 mm Safety Banana Plug Leads Quantities: Yellow, 30 cm (12 in) 20pcs
  8. Red, 60 cm (24 in) 10pcs
  9. Blue, 90 cm (36 in) 4pcs
  10. 2 mm Safety Banana Plug Leads Characteristics: Cross Section 0.5 mm²(987 cmils)
  11. Rated Current 10 A
  12. Rated Voltage 30 V ac / 60 V dc
  13. 2 mm Safety Banana Plug Leads Quantities
  14. Red, 60 cm (24 in) 4pcs
  15. Four-Quadrant Dynamometer/Power Supply

3.Standard Functions (manual control)

  1. Dynamometer operating mode
  2. Two-Quadrant, Constant-Torque Brake
  3. Clockwise Prime Mover/Brake
  4. Counterclockwise Prime Mover/Brake
  5. Clockwise Constant-Speed Prime Mover/Brake

 

  1. Counterclockwise Constant-Speed Prime Mover/Brake
  2. Positive Constant-Torque Prime Mover/Brake
  3. Negative Constant-Torque Prime Mover/Brake
  4. Control functions
  5. Two-Quadrant, Constant-Torque Brake
  6. Clockwise Prime Mover/Brake
  7. Counterclockwise Prime Mover/Brake
  8. Clockwise Constant-Speed Prime Mover/Brake
  9. Counterclockwise Constant-Speed Prime Mover/Brake
  10. Positive Constant-Torque Prime Mover/Brake
  11. Negative Constant-Torque Prime Mover/Brake
  12. Positive Voltage Source
  13. Negative Voltage Source
  14. Positive Current Source
  15. Negative Current Source
  16. 200 V DC Bus
  17. Lead-Acid Battery Float Charger
  18. Power Supply operating mode
  19. Positive Voltage Source
  20. Negative Voltage Source
  21. 200 V DC Bus
  22. Positive Current Source
  23. Negative Current Source
  24. 50 Hz Power Source
  25. 60 Hz Power Source
  26. Lead-Acid Battery Float Charger
  27. Two-Quadrant, Constant-Torque Brake
  28. Torque 0-3 N·m (26.55 lbf·in)
  29. Clockwise/Counterclockwise Prime Mover/Brake
  30. Speed 0-2500 r/min
  31. Clockwise/Counterclockwise Constant-Speed
  32. Prime Mover/Brake
  33. Speed 0-2500 r/min
  34. Positive/Negative Constant-Torque Prime Mover/Brake
  35. Torque 0-3 N·m (26.55 lbf·in)
  36. Positive/Negative Voltage Source: Voltage 0 to ±150 V
  37. Positive/Negative Current Source: Current 0 to ±5 A
  38. 50 Hz/60 Hz Power Source
  39. No-Load Voltage 0-140 V
  40. 200 V DC Bus: Status On or off
  41. Lead-Acid Battery Float Charger: Float Voltage 0-150 V

4.    Standard Functions (computer-based control)

  • Dynamometer operating mode
  • Two-Quadrant, Constant-Torque Brake
  • Clockwise Prime Mover/Brake
  • Counterclockwise Prime Mover/Brake
  • Clockwise Constant-Speed Prime Mover/Brake
  • Counterclockwise Constant-Speed Prime Mover/Brake
  • Positive Constant-Torque Prime Mover/Brake
  • Negative Constant-Torque Prime Mover/Brake
  • Four-Quadrant Constant-Speed Prime Mover/Brake
  • Speed Sweep
  • Power Supply operating mode
  • Positive Voltage Source
  • Negative Voltage Source
  • DC Voltage Source
  • Positive Current Source
  • Negative Current Source
  • DC Current Source
  • 50 Hz Power Source
  • 60 Hz Power Source
  • AC Power Source
  • Lead-Acid Battery Float Charger

Control functions

  • Two-Quadrant, Constant-Torque Brake
  • Clockwise Prime Mover/Brake
  • Counterclockwise Prime Mover/Brake
  • Clockwise Constant-Speed Prime Mover/Brake
  • Counterclockwise Constant-Speed Prime Mover/Brake
  • Positive Constant-Torque Prime Mover/Brake
  • Negative Constant-Torque Prime Mover/Brake
  • Four-Quadrant, Constant-Speed Prime Mover/Brake
  • Speed Sweep
  • Mechanical Load
  • Positive Voltage Source
  • Negative Voltage Source
  • DC Voltage Source
  • Positive Current Source
  • Negative Current Source
  • DC Current Source
  • 50 Hz Power Source
  • 60 Hz Power Source
  • AC Power Source
  • Lead-Acid Battery Float Charger

Specifications:

  • Two-Quadrant, Constant-Torque Brake
  • Torque Control:  Software knob, 8960 module knob, or 8960 command input
  • Torque: :0-3 N·m (26.55 lbf·in)
  • Pulley Ratio: 24:24, 24:12, or 24:32
  • Clockwise/Counterclockwise Prime Mover/Brake
  • Speed Control: Software knob, 8960 module knob, or 8960 command input
  • Speed : 0-2500 r/min
  • Pulley Ratio: 24:24, 24:12, or 24:32
  • Positive/Negative Constant-Torque Prime Mover/Brake
  • Torque Control: Software knob, 8960 module knob, or 8960 command input
  • Torque: 0-3 N·m (26.55 lbf·in)
  • Pulley Ratio: 24:24, 24:12, or 24:32
  • Four-Quadrant, Constant-Speed Prime Mover/Brake
  • Speed Sweep
  • Start Speed : 3000 r/min to 3000 r/min
  • Finish Speed : 3000 r/min to 3000 r/min
  • Number of Steps : 0-50 steps
  • Step Duration : 2-10 s
  • Record Data to Table: Yes or no
  • Pulley Ratio : 24:24, 24:12, or 24:32

Mechanical Load: 

  • Load Type : Flywheel, fan, grinder, conveyor, calender, crane, user defined
  • Inertia: 0.005-1 kg·m²(0.119-23.73 lb·ft²)
  • Friction Torque : 0.05-3 N·m (0.44-26.55 lbf·in)
  • Pulley Ratio : 24:24, 24:12, or 24:32
  • Positive/Negative Voltage Source: 
  • Voltage Control : Software knob, 8960 module knob, or 8960 command input 
  • Voltage : 0 V to 147 V / -147 V to 0 V
  • DC Voltage Source : -147 V to 147 V
  • Positive/Negative Current Source
  • Current Control  : Software knob, 8960 module knob, or 8960 command input
  • Current : 0 A to 5 A / -5 A to 0 A
  • DC Current Source
  • Current Control: Software knob, 8960 module knob, or 8960 command input
  • Current : 5 A to 5 A
  • 50 Hz/60 Hz Power Source
  • Voltage Control : Software knob, 8960 module knob, or 8960 command input
  • No-Load Voltage: 0-140 V

Accessories

  • Compatible pc
  • Printed Instruction manual in English
  • Hp 3 in 1 duplex printer
  • 11. Mobile workstation
  • Multimeters Module
  • Digital Multimeter
  • Storage Shelves
  • Others
  • All instruction manuals to be in both printed and CD written and in English version
  • Warranty:24 months under Suppliers warranty certificate
  • The supplier must attach evidence of the equipment(s) under supply
     

 

ACQUISITION AND CONTROL INTERFACE Spec: 

  • ifications
  • Insulated Voltage Inputs (4)
  • Range (Low / High Scales) : 80 to +80 V / -800 to + 800 V (user-selectable through software)
  • Impedance (Low / High Scales) : 326.6 kΩ / 3.25 MΩ
  • Bandwidth : DC to 65 kHz (-3 dB)
  • Accuracy : 1% (dc to 10 kHz)
  • Insulation : 800 V
  • Measurement Category: CAT II (283 V ac/400 V dc versus ground)
  • Insulated Current Inputs (4)
  • Range (Low / High Scales) :  -4 to +4 A / -40 to + 40 A (25 A rms)
  • Impedance (Low / High Scales) : 5 mΩ / 50 mΩ
  • Bandwidth : DC to 65 kHz (-3 dB)
  • Accuracy : 1% (dc to 10 kHz)
  • Insulation : 800 V
  • Measurement Category : CAT II (283 V ac/400 V dc versus ground)
  • Analog Inputs (8)
  • Voltage Range : -10 to +10 V
  • Impedance : > 10 MΩ
  • Bandwidth :  DC to 125 kHz
  • Measured Parameters : User-selectable through software
  • Parameter-to-Voltage Ratio User-determined through software
  • A/D Converter for Insulated and Analog Inputs (16)
  • Type : Successive approximation
  • Resolution : 12 bits
  • Integral Non-Linearity : ≤ ±1.5 LSB
  • Differential Non-Linearity : ≤ ±1 LSB
  • Maximum Sampling Rate : 600 ksamples/s (one channel)
  • FIFO Buffer Size : 16 ksamples
  • Analog Outputs (2)
  • Voltage Range (2) :  -10 to +10 V
  • Operational Load Impedance:> 600 Ω
  • D/A Converter for Analog Outputs (2)
  • Type : Resistor string
  • Resolution : 12 bits
  • Integral Non-Linearity : ≤ ±8 LSB
  • Differential Non-Linearity : -0.5 to +0.7 LSB
  • Maximum Input Frequency : 50 kHz
  • Impedance : 5 kΩ
  • Digital Outputs (9)
  • Types: Control (6 on a DB9 connector and 2 on 2 mm banana jacks), synchronization (1 on a DB9 connector)
  • Signal Level:  0-5 V (TTL compatible)
  • Maximum Output Frequency: 20 kHz (software-limited)
  • Impedance: 200 Ω
  • Metering: Number of Meters: 18
  • Sampling Window: 320 ms or user adjusted through software (11.4-819 ms)
  • Sampling Frequency (each meter): 6.4 kHz or user adjusted through software (2.5-179.2 kHz)
  • Display Type: Digital or analog, user selectable through software

Oscilloscope:

  • Number of Channels: 8
  • Vertical Sensitivity: 2-500 V/div.
  • Time Base: 0.0001-10 s/div.
  • Sampling Window: 20 x selected time base (software triggering) / 10 x selected time base
  • (hardware triggering)
  • Sampling Frequency: 512 samples per measured parameter per horizontal sweep, up to a maximum of 512 kHz

Enquiry Form