Control Trainer

Order Code: 21225242.8

Category: General Lab Equipment I

Supply Brand New Automatic Trainer Control with proportional Controller, Two position Controller, PI/PID Controller, Servo Control System(AC/DC),Steper Motor Controller Module Built in power supply: DC supply: +12V,500mA 1phase sine reference for ...



SPECIFICATION

  • Supply Brand New Automatic Trainer Control with proportional Controller, Two position Controller, PI/PID Controller, Servo Control System(AC/DC),Steper Motor Controller Module Built in power supply: DC supply: +12V,500mA 1phase sine reference for cosine firing 30Vpp max 17Vdc, 500mAunregulated for driving pulse X'mer Variable DC power supply : 7 to 14V/3A Display A) DPM - 2Nos. For Temp. up to 100 C & intensity in Lux (2000) For speed 2000 rpm & voltage up to 20V. B) Analog Meter - 2Nos. Centre zero for display of process error (+9V) For MV/SP (0-2.5V) Operating voltage Switch selectable 220-240Vac, ±10%, 50Hz, 75VA PC (P4/XP/WIN7/FAT32) based PID controller (Optional): Online monitoring / Data acquisition / PID Software: on Installable (CD) works under XP, WIN7. PC with parallel port / USB needed. Operating modes Simulator Mode Tests data already stored in files (*.txt) & Drawing graph for all P,PI,PD & PID modes. ProcessMonitoring Mode Drawing graphs of analog data presented at CH 0 & CH of Computer Interface. Cursors for X & Y axis for measurement & online graphs savings for reproduction
  • PID controller Mode
  • PID controller with parameters like Integral Time Ti (0.01-64000), Sampling Time Ts (0.1- 99.9), Derivative Time Td (0.1-99.9), Proportional Band Pb(1- 999), Derivative Gain Kd(1-999), Set Value Rn (0-99.9), PID output Upper Limit Uh(0-99.9), PID output Lower Limit Ul (0-99.9).
  • Facility to set units for output viz. Percentage (%), C, RPM, 2 Voltage(V), mm, Computer Interface Adapter / CIA: Optoisolated Adaptor to prevent damage to PC parallel port (25 pin LPT) 4 ADC channels: 0 to 2.5V full scale.
  • 1 DAC channel: O/P 2.5 V FS.
  • V to I Function block: Input: 0-2.5Vdc, Output: 0-20 or 4-20mA, in 100E load Max
  • USB IO module to interface 25 pin D connector on CIA panel to USB PC port
  • V to PWM function block : I/P-0-2.5V, O/P-1KHz PWM O/P±9V. Analog PID (APID) controller with built in low freq. function generator Controller selection P,PI,PD,PID with slide switch
  • Parameter settings: Integral Time Ti (0.5-25Sec), Derivative Time Td (0- 2Sec), Proportional Band Pb (5-200%), Set point (-9V- +9V)
  • Operating modes: Fast (X 100/10mSec) for oscilloscope, Slow ( X 0.1/1Sec) for PC interface.
  • 2 No. Level shifter converting process O/p (+9V) to 0-2.5V for PC interface & Actuator panel Test points for Process Error, Set Point (Rn), Measured Value (Cn), Controller output (Un).  Built in function generator
  • O/p freq. range from 0.016Hz to 166Hz, 4 steps & fine control pot. Variable amplitude control 0 to +9V.
  • Modular Expt. Panels offered Process Simulator Panel Thyristor Actuator panel (TAP)
  • Stepper Motor Demonstrator Expt. Panel Servo Interface panel (SIP)
  • Computer Interface panel
  • Temperature/Light module High Temperature Module DC & AC Servo Position Control
  • Stepper Motor
  • AC Voltage Servo Stabilizer Inverted Pendulum

Enquiry Form