10 MHz DDS Function generator

Order Code: 22235476.2

Category: General Lab Equipment II

Output frequency : 1μHz~10MHz Output waveform : 32 built-in waveforms, including Sine, Square, Triangle, Ramp, Pulse, etc. Waveform length : 1024 points Vertical resolution :8 bits Sampling rate :100MSa/s Sine Harmonic distortion : &g...



SPECIFICATION

  • Output frequency : 1μHz~10MHz
  • Output waveform : 32 built-in waveforms, including Sine, Square, Triangle, Ramp, Pulse, etc.
  • Waveform length : 1024 points
  • Vertical resolution :8 bits
  • Sampling rate :100MSa/s
  • Sine Harmonic distortion : ≥40dBc (<1MHz); ≥35dBc (1~20MHz)
  • Total distortion : ≤1% (20Hz~200kHz)
  • Square Rise/fall time : ≤35ns
  • Overshoot : ≤10%
  • Duty cycle : 1%~99%

Frequency

  • Range Sine: 1μHz~10MHz
  • Range Square : 1μHz~5MHz
  • Range Other : 1μHz~1MHz
  • Resolution : 1μHz
  • Accuracy : ±5x10-5
  • Stability : ±5x10-6 /3hours

Sweep

  • Parameter : Frequency, Amplitude
  • Range : Free to set start and stop point
  • Time : 100ms~900s
  • Direction : Up, Down, Up-Down
  • Mode : Linearity, Logarithmic
  • Control : Auto sweep or manual sweep

Frequency Modulation (FM)

  • Carrier signal : CHA signal
  • Modulating signal : CHB or external signal
  • Deviation : 0%~20%

Shift Keying

  • FSK : Free to set the hop frequency and the carrier frequency
  • ASK : Free to set the hop amplitude and the carrier amplitude
  • PSK : Hop phase: 0~360°, resolution: 1°
  • Alternative rate : 10ms~60s

Burst

  • Carrier signal : CHA signal
  • Trigger signal : TTL_A signal
  • Burst counts : 1~65000 cycles
  • Trigger source : Internal TTL, External, Single CHB output characteristics
  • Output waveform : 32 built-in waveforms, including Sine, Square, Triangle, Ramp,

Pulse, etc.

  • Waveform length : 1024 points
  • Vertical resolution: 8 bits
  • Sampling rate : 12.5MSa/s
  • Frequency range Sine: 1μHz~1MHz; Other: 1μHz~100kHz
  • Frequency resolution : 1μHz
  • Frequency accuracy : ±1x10-5
  • Amplitude range : 50mVpp~20Vpp (open circuit)
  • Amplitude resolution : 20mVpp
  • Output impedance : 50Ω
  • CHB signal is used as burst signal
  • Carrier signal : CHB signal
  • Trigger signal : TTL_B signal
  • Burst counts : 1~65000 cycles
  • Trigger source : Internal TTL, External, Single

TTL output

  • Waveform : Square, rise/fall time ≤20ns
  • Frequency: 10mHz~1MHz
  • Amplitude : TTL, CMOS compatible, low<0.3V, high>4V

Frequency counter

  • Frequency range : 1Hz~200MHz
  • Input amplitude : 100mVpp~20Vpp

Power amplifier (optional)

  • Max. output power : 7W (8Ω), 1W (50Ω)
  • Max. output voltage : 22Vpp
  • Frequency bandwidth : 1Hz~200kHz

Enquiry Form